ASTM A515 Grade 60, 65 and 70 Steel Plate

  • Home >>


ASTM A515 Grade 60, Grade 65 and Grade 70 steel plates are carbon-silicon pressure-vessel steels intended primarily for welded boilers and pressure vessels operating at intermediate and higher temperatures. The three grades provide progressively higher tensile-strength levels, ranging from 415–550 MPa for Grade 60 to 485–620 MPa for Grade 70, allowing the material strength to be matched to different pressure-equipment designs. ASTM A515 steel is killed and produced to a coarse austenitic grain-size practice, and is used for pressure-vessel shells, boiler components, heat exchangers, storage vessels and other welded pressure-containing equipment exposed to elevated-temperature service.

Key Properties:

  • Chemical Composition: ASTM A515 plates typically consist of carbon, manganese, phosphorus, sulfur, and silicon, with specific limits on these elements to achieve desired mechanical properties.
  • Mechanical Properties:
    • Grade 60: Yield Strength: Minimum 207 MPa (30,000 psi); Tensile Strength: 415 - 550 MPa (60,000 - 80,000 psi); Elongation: Minimum 21% in 200 mm.
    • Grade 65: Yield Strength: Minimum 241 MPa (35,000 psi); Tensile Strength: 450 - 590 MPa (65,000 - 85,000 psi); Elongation: Minimum 20% in 200 mm.
    • Grade 70: Yield Strength: Minimum 276 MPa (40,000 psi); Tensile Strength: 485 - 620 MPa (70,000 - 90,000 psi); Elongation: Minimum 19% in 200 mm.

Applications:

ASTM A515 steel plates are commonly used in:

  • Manufacturing of pressure vessels for the oil and gas industry.
  • Construction of boilers and heat exchangers.
  • Fabrication of industrial storage tanks and other pressure-sensitive equipment.
  • Applications where high strength and durability are required, especially in high-temperature environments.

In summary, ASTM A515 steel plates provide a robust and reliable solution for various applications in the pressure vessel and boiler manufacturing sectors, ensuring safety and performance in demanding conditions.


It covers three grades ranged by different strength as follows:

Grade U.S. [Sl]

Tensile Strength, ksi [MPa]

60 [415]

60-80 [415-550]

65 [450]

65-85 [450-585]

70 [485]

70-90 [485-620]

The maximum thickness of plates is limited only by the capacity of the composition to meet the specified mechanical property requirements; however, current practice normally limits the maximum thickness of plates furnished under this specification as follows:

Grade U.S. [Sl]

Maximum Thickness, in. [mm]

60 [415]

8 [200]

65 [450]

8 [200]

70 [485]

8 [200]

For plates produced from coil and finished without heat treatment or with stress relieving only, the additional requirements including test report shall comply with Specification A20/A20M.

Reference Documents

ASTM Standard:

  • A20/A20M: Specification for General Requirements for Steel Plates for pressure Vessels
  • A435/A435:  Ultrasonic Examination Specification for Straight-Beam  of Steel Plates
  • A577/A577M: For Ultrasonic Angle-Beam Examination of Steel Plates
  • A578/A578M: For Straight-Beam Ultrasonic Examination of Rolles Steel Plates for Special Applications

General Requirements and Ordering Information

The plates shall confirm to ASTM A20/A20M.

  • Testing and retesting methods, procedures;
  • Permissible tolerances in dimensions and mass, quality;
  • Repair of defects;
  • Marking, loading and ordering information;
  • Coils are excluded from this specifcation in case cutted to the plates form.

Material and Manufacture

The steel shall be killed and made to a coarse austenitic grain size practice.

Heat Treatment

ASTM A515 plates thickness in 50 mm [2 inch] thickness and under are normally supplied with as-rolled condition, unless it is ordered as requested.

Plates over 50 mm [2 in] in thickness shall be normalized.

Chemical Composition

Chemical Requirements

Elements

Composition, %

Grade 60 [Grade 415]

Grade 65 [Grade 450]

Grade 70 [Grade 485]

Carbon, max: A,B

1 in. [25 mm] and under

0.24

0.28

0.31

Over 1 to 2 in. [25 to 50 mm], incl

0.27

0.31

0.33

Over 2 to 4 in. [50 to 100 mm], incl

0.29

0.33

0.35

Over 4 to 8 in, [100 to 200], incl

0.31

0.33

0.35

Over 8 in. [200 mm]

0.31

0.33

0.35

Manganese, B max

Heat analysis

0.90

0.90

1.2

Product analysis

0.98

0.98

1.3

Phosphorus, max A

0.025

0.025

0.025

Sulfur, max A

0.025

0.025

0.02

Silicon:

Heat analysis

0.15-0.40

0.15-0.40

0.15-0.40

Product analysis

0.13-0.45

0.13-0.45

0.13-0.45

A  Applies to both heat and product analyses.

B  For each reduction of 0.01 percentage point below the specified maximum for carbon, an increase of 0.06 percentage point above the specified maximum for manganese is permitted, up to a maximum of 1.5% by heat analysis and 1.6% by product analysis.

Mechanical Properties

Tensile Requirements


Grade

60 [415]

65 [450]

70 [485]

Tensile strength, ksi [MPa]

60-80 [415-550]

65-85 [450-585]

70-90 [485-620]

Yield strength, min, ksi [MPa]

32 [220]

35 [240]

38 [260]

Elongation in 8 in. [200 mm], min, % A

21

19

17

Elongation in 2 in. [50 mm], min, % A

25

23

21

 A See Specification A20/A20M for elongation adjustment.

Our Supply Range:

Description: Carbon Steel ASTM A515 Grade 60, 65, 70
Manufacturing Types: Hot Rolled
Thickness: 2mm to 150 mm
Width: 0.6m to 3m
Length: 6m, 12m, customized
Surface: Natural, Painted
Packing: Standard sea packing, bundled with streel strip.

FAQ

Q1: Does ASTM A515 Grade 70 have a higher allowable service temperature than Grade 60 or Grade 65?
A1: No. The grade numbers identify different strength levels, not different allowable operating temperatures. Service temperature is determined by the applicable design code and project requirements.

Q2: Does ASTM A515 have a fixed maximum plate thickness?
A2: No. Maximum thickness is limited by the ability of the material composition to meet the specified mechanical properties.

Q3: Can ASTM A515 pressure-vessel plate be produced from coil?
A3: Yes. Plate produced from coil may require additional testing and reporting under ASTM A20/A20M before finished-plate compliance is established.

Q4: If A515 Grade 70 and A516 Grade 70 have similar strength ranges, are they interchangeable?
A4: No. A515 is intended for intermediate- and higher-temperature service, while A516 emphasizes improved notch toughness for moderate- and lower-temperature pressure-vessel service.

Related Products:


ASTM A283 Grade C, D Plates
ASTM A516 Grade 70, 65, 60 Steel Plate
ASTM A285 Grade A, B, C Plate
ASTM A537 Class 1, 2 Plates
ASTM A572 Grade 50, 60 Steel Plates
AH36, DH36, EH36 Shipbuiding Steel Plates
Carbon Steel Plate
304 Stainless Steel Plate